Click to go to Forum Home Click to go to maXbimmer Home

Go Back   maXbimmer Forums > maXimum Tech > Classics
User Name
Password


Welcome to Maxbimmer.com!

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

Reply
 
Thread Tools Rate Thread Display Modes
Old 08-16-2018, 02:28 PM   #76
T.Dot_E30
Classifieds Moderator
 
T.Dot_E30's Avatar
 
Join Date: Apr 2003
Location: GTA
Posts: 9,782


Awesome, starting to take shape!
T.Dot_E30 is offline   Reply With Quote
Old 08-26-2018, 10:03 PM   #77
Bullet Ride
Cars in Perpetual Repair
 
Bullet Ride's Avatar
 
Join Date: Nov 2007
Location: Guelph
Posts: 6,013
Update from this weekend, spent some time Saturday buttoning up the rear sub-frame. I never took any pics but the gas tanks are back up. After bolting on my garagtastic poly subframe mounts and lifting the sub-frame back up into place I noticed that the diff hanger was too long. That's because the flange on the garagtastic mounts is welded in the middle of the bushing whereas the factory flange is offset, this caused the sub-frame to be raised about 3/4". So I sliced the hanger in half... trimmed some out and tacked it to test fit...



Fitment was good, so I welded it up, painted and installed...



After that the axles went back on along with the BC coils...



Man those rear axle nuts are crazy... 295-347ft-lb torque spec! My torque wrench only goes to 150ft/lbs... just went by feel after that with a bigger breaker bar until the castle nut lined up with a pin hole.

Gasser style haha

__________________
Bullet Ride is offline   Reply With Quote
Old 08-31-2018, 06:10 PM   #78
craz azn
6th Gear Member
 
craz azn's Avatar
 
Join Date: Feb 2004
Location: Port Perry
Posts: 7,632
Send a message via MSN to craz azn
__________________

Rippin' Proper | Youtube | Vimeo |
craz azn is offline   Reply With Quote
Old 09-13-2018, 02:50 PM   #79
Bullet Ride
Cars in Perpetual Repair
 
Bullet Ride's Avatar
 
Join Date: Nov 2007
Location: Guelph
Posts: 6,013
Update on the coilovers...

The gland nuts on the shock assembly were rusted good and tight... fortunately I didn't need that part anymore... it just meant that I couldn't pull the shock out before cutting the housing....



That meant that I had to very carefully cut through the housing without cutting into the shock body... #TrustMeImAnEngineer...



Success

After that it was just a matter of wire wheeling and welding...







And back on the car....



__________________
Bullet Ride is offline   Reply With Quote
Old 10-19-2018, 09:49 AM   #80
Bullet Ride
Cars in Perpetual Repair
 
Bullet Ride's Avatar
 
Join Date: Nov 2007
Location: Guelph
Posts: 6,013
It's been a while... because I bought a house and am knee deep in renovations... progress will be slow for the next few months...

Recently on thanksgiving weekend, I gave thanks for the EFI M10 motor that I picked up for free a while back, because the one that I had bought before that one must have sat unused with no oil in it for a long time and had too much rust in the bores to use as-is.

So I swapped engines on the stand and started basic tear down to inspect condition and clean things up...









It looks like someone must have had this motor out for a refresh at some point because the block has good coat of black paint on it and some newer yellow zinc bolts on some brackets. I tried picking at the paint and it's on there good, not just a quick and dirty job over the old flaky rust that tends to accumulate on these old blocks.



The valvetrain was also really clean, leading me to believe that the head had been off recently... hopefully not for any terrible reasons...



The only thing I found so far was that the head has a hairline crack on one of the spark plug holes that had been sealed up.



Since it's not structural and there is no evidence on the outside of the head or block that it had been leaking recently, I'm just going to leave it for now. My goal right now is to get the engine in the car and start working on the wiring harness for megasquirt. I have a spare head on the motor I'm not using that I'll clean up and have ready to go in the event that this one starts leaking.

That's all for now.
__________________
Bullet Ride is offline   Reply With Quote
Old 11-20-2018, 12:20 PM   #81
Bullet Ride
Cars in Perpetual Repair
 
Bullet Ride's Avatar
 
Join Date: Nov 2007
Location: Guelph
Posts: 6,013
Minor update:

Had a few hours to spare this weekend so I continued working on cleaning up the motor.
I'm pretty well done that task now. Next I'll have to give a few things a coat of paint, then I can re-seal it and drop it into the car so I can start working on the wiring harness.



__________________
Bullet Ride is offline   Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 08:57 AM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Maxbimmer Copyright 2001 - 2018